提交SMOD ATSC IMX APP版本 V122

2026-07-16 14:35:59 +08:00
commit 7601c270d5
485 changed files with 255032 additions and 0 deletions
@@ -0,0 +1,322 @@
+
+#ifndef __CONFIG_H__
+#define __CONFIG_H__
+
+
+#define		AW_ATSC_5X		1
+
+//判断是否定义美国或者全波版本(5K+)
+#if USA_ATSC_5X
+#define  USA_ATSC_5X  1
+#else
+#define  USA_ATSC_5X  0
+#endif
+
+#if AW_ATSC_5X
+#define  AW_ATSC_5X  1
+#else
+#define  AW_ATSC_5X  0
+#endif
+
+#if USA_ATSC_5X && AW_ATSC_5X
+#error "Only could define one exciter type!!!"
+#endif
+
+#if (USA_ATSC_5X==0) && (AW_ATSC_5X==0)
+#error "Must define The exciter type!!!"
+#endif
+
+#define xQueueHandle  int*
+#define tskIDLE_PRIORITY   1
+
+
+#ifndef USE_HW_REPT
+#define USE_HW_REPT							0
+#endif
+
+#if 1
+#define USE_DRY_LOOP                0   //@NOT_USED
+#endif
+
+//------------------usr-define------------------------
+//测试用-发布时需要开放
+#define USE_DBG_PASS_TUNER_INIT     0 //跳过tuner init
+
+
+#define USE_UART_DEV_LINK           1
+
+/*
+ * Prefer the local key/LCD path when the single-core CPU is busy with IQ
+ * analysis.  Set to 0 to restore the original thread priorities.
+ */
+#define USE_UI_RESPONSE_PRIORITY    1
+
+/*
+ * Keep the physical RF output muted while FPGA/ADRV9009/JESD/DPD are being
+ * initialized.  The saved/user-requested RF state is restored only after the
+ * whole RF chain is ready, avoiding boot transients at the output.
+ */
+#define USE_DELAYED_RF_ENABLE       1
+#define RF_BOOT_STABLE_DELAY_MS     2000
+//---------------------------------------------------
+//if   use korea -- need check ca     //V173
+//else use us    -- ca default bypass
+#define USE_KOREA_VERSION			(0)
+
+//#define SPL_CURV_LOAD_STORE         0
+
+
+#if USA_ATSC_5X
+
+ #if USE_HW_REPT
+    #define SW_VERSION          "V6.1A_150107T"
+ #else
+    #define SW_VERSION          "V6.1A_150107"
+ #endif
+ 
+    #define ERR_TO_LCM          1
+    #define USE_DRYLOOP_I2C     0     //美国5K+,暂时使用串口模式
+    #define USE_TUNER_88436     1     //TUNER88436 外部解码 tuner18273 需要fpga解码,18273只是个高频头
+    #define USE_TUNER_18273     0     //两个只能同时使用1个
+
+    #define USE_PSTS            0
+    #define USE_NEW_DIO_MODE    0    //是否使用美国新的dio模式 在原先的dio基础上对部分按键做了重定义
+#elif AW_ATSC_5X
+
+ #if USE_HW_REPT
+    #undef  USE_DBG_PASS_TUNER_INIT
+    #define USE_DBG_PASS_TUNER_INIT   (1)
+    #define SW_VERSION          "V5.2AW_210902T"  //"V5.2AW_210822T" 
+ #else
+    #define SW_VERSION          "V5.2AW_220331R"  //"V5.2AW_211217" 
+ #endif
+
+    #define ERR_TO_LCM          1
+    #define USE_DRYLOOP_I2C     0
+    #define USE_TUNER_88436     0
+    #define USE_TUNER_18273     0     //三个只能同时使用1个,或者不用
+
+    #define USE_PSTS            1
+    #define USE_NEW_DIO_MODE    1    //是否使用美国新的dio模式 在原先的dio基础上对部分按键做了重定义
+#endif
+
+
+#define USE_STD_USART_SEND_RECV     1
+
+/*开启该功能时，需要调整网页ADPC的选项*/
+#define USE_UPDATA5                 0//禁用
+#define USE_RESET_TCP               (1)//重置tcp
+#define USE_UART_CMD_PRINT_LWIP     (1)//串口命令可以打印:80 46 06 70 3C 96
+
+//调试使用
+#define DBG_ADPC_NO_FEEDBACK_ERR    0
+
+//------------------<<<<<<<<<<------------------------
+
+#define ATSC_TITLE_LEN          16
+#define ATSC_WEB_TITLE          "Digital Exciter"
+#define SNTP_TIME_STRING_LEN    8
+#define SNTP_DATE_STRING_LEN    10
+
+
+
+
+#define I2C_MAX_NUM       5
+
+#define DEBUG_AUTO_ADPC   0
+#define ATSC_USA_AMP      1
+
+
+
+//@TO_DISABLE
+#define I2C_SOFT_GPIO     0    //只能为1
+
+#define USE_SONYCXD6801GL   1
+
+
+#if ((USE_TUNER_18273==1)&&(USE_TUNER_88436==1)) || ((USE_TUNER_18273==1)&&(USE_SONYCXD6801GL==1)) || ((USE_TUNER_88436==1)&&(USE_SONYCXD6801GL==1))
+#error "must choose only one tuner type!"
+#endif
+
+#if (USE_TUNER_18273==1)||(USE_TUNER_88436==1)||(USE_SONYCXD6801GL==1)
+#define USE_TUNER        1   //1
+#else
+#define USE_TUNER        0
+#endif
+
+
+//++++++++++++++++++++++++++++++++++++++++++
+#if 1//usr_def
+#define TMP_DISABLE_BOOT_SNR_UPDATE	(0)
+
+
+#define  DBG_DISABLE_I2C    		(0)
+#define  DBG_DISABLE_TUNER			(0)
+#if DBG_DISABLE_TUNER
+ #ifdef USE_TUNER
+ #undef USE_TUNER
+ #define USE_TUNER    				(0)
+ #endif
+#endif
+
+#define  DBG_I2C_ERR_DELAY			1
+
+//#define USE_TUNER		1
+
+//暂时先关闭
+#define THR_GPS			0
+
+#define THR_LCD			1
+
+//+++++++++++++++++++++++++++++++++++++++++++
+
+
+#define NO_USE	0 //@NOT_USED
+
+#define ETH_UPGRADE 0
+/*#ifndef ETH_UPGRADE  //默认打开升级模式
+#define ETH_UPGRADE 1
+#else
+#define ETH_UPGRADE 0
+#endif*/
+
+#define TMP_UNUSE_LCD			1
+
+//@NOT_USED
+//#define USE_GPS                 1
+#define USE_GPS                 1
+
+//@TMP_UNUSED_FOR_MAKE
+#define TMP_UNUSE_GPS_TIME		0
+
+//@TMP_UNUSED_FOR_MAKE
+#define NEED_TO_EN				0
+
+//NEED_TO_EN
+#define FPGA_UP_MSG				1
+#define NEED_SEND_ALM			0
+
+//对于5段地址冲突的部分需要禁用
+#define ADDR_CONFLICT_DISABLED		1
+
+#endif//usr_def
+//+++++++++++++++++++++++++++++++++++++++
+
+
+#define SYSTICKHZ               (configTICK_RATE_HZ)
+#define SYSTICKMS               (1000 / configTICK_RATE_HZ)
+
+#define E2_ROM_SIZE             (32*1024)  // e2rom 32Kbyte
+#define E2_ROM_PAGE             (64)     // e2rom 页
+
+
+#define USE_SWAP_DATA           1
+#define USE_SPI_FLASH           1     //flash开关
+#define SHOW_DEBUG_INFO         0
+#define TEST_E2_ROM             0
+#define SCAN_NEED_CHANGE_MODE   0
+#define USE_CTRL_MODE           1
+#define USE_HTTP_LOGIN          1
+#define USE_TCP_COMM            1    //网络通讯
+
+#define USE_NEW_FPGA            1
+
+
+#define USE_LCD_CACHE           1
+#define USE_BIG_LCD             1
+#define USE_HTTP                1
+#define FPGA_UPGRADE            1
+
+#define USE_SNR_ADJ             1
+
+#define UPGRADE_LISTEN_PORT     1234
+#define TCP_COMM_PORT           4003
+#define TCP_COMM_DATA_PORT      4017
+
+
+#define SYSTICK_INT_PRIORITY    0x80
+#define ETHERNET_INT_PRIORITY   0xC0
+
+#define ALARM_USE_UDP           1 //那个版本以后,待定
+
+
+///////////////////////////////////////////////////////////////////////////
+
+//#define USE_NLOGO_VER			0 //对于正式发布的atsc5x+需要配0
+
+/*#if USE_NLOGO_VER
+#define TEMPREATURE_DEGREE      1 //温度
+#else
+#define TEMPREATURE_DEGREE      0 //温度
+#endif**/
+
+//系统组件配置
+
+
+#define USE_SPECT_DATA_TASK     1    // 是否需要通过tcp向上位机传送数据  8000型有此功能
+#define USE_ADPC_LONG           1    // 预校正加长代码
+#define USE_NEW_AGC             0
+#define USE_TS_CHECK            1
+#define USE_GPS_UBLOX6          1
+#define USE_GPS_CHECK           1
+#define USE_TS2IP               1
+#define USE_SNTP_SNYC_TIME      1
+#define USE_TEMPERATURE_CHECK   1
+#define USE_OVERFLOW_CHECK      1
+
+#define USE_NETWORK_DNS         0   // 是否配置dns
+#define USE_NEW_POWER_CFG       1   // HMC472 + ADRV9009 power allocation
+#define USE_FREQ_CHANGE_RESET_PWR 1 // 切换频点后是否先将输出功率降到-25dB
+
+
+#if USE_BIG_LCD
+    #define LCD_CHAR_NUM        40
+#else
+    #define LCD_CHAR_NUM        20
+#endif
+
+
+#define TEST_GPS_MOUDLE         1
+
+// RF 相关注释
+#define   setbit(x,y)      (x)= (1<<(y))        //将X的第Y位置1,清其他位,
+#define   setbits(x,y)     (x)|=(1<<(y))        //将X的第Y位置1,保留其他位,
+#define   clrbit(x,y)      (x)&=~(1<<(y))       //将X的第Y位清0,
+#define   clrbits(x,y,z)   (x)&=~((z)<<(y))     //从Y位开始,以Z为整体对X某些位清0,
+#define   _STATUS_RF     0   //Bit0=1无输出 为0正常  串口返回时 单独 "或1" 处理,
+#define   _KEY_RF        1   //Bit 1
+#define   _KEY_WH        2   //Bit 2
+#define   _KEY_TX        2   //Bit 2
+#define   _LOCAL_REMOET  2   //Bit 2
+#define   _PIN_DRYLOOP   3
+#define   _MISS_OTHER    4
+#define   _MISS_TS       5
+#define   _MISS_10M      6
+#define   _MISS_1PPS     7
+
+#define    MAC_DEFAULT   (0x13<<16) | (0x05<<8) | (0x03)
+
+#define  BAK_PARA_CHECK     1
+#define  DEBUG_ERR_CHECK    0  // WC屏参数激励器不试用，可用来调试
+//Bit 0 为0时正常，为1时不正常
+#define  BAK_ERR_OK         0
+#define  BAK_ERR_ERR        1
+#define  BAK_ERR_TXFREQ     1<<1
+#define  BAK_ERR_RXFREQ     1<<2
+#define  BAK_ERR_POWER      1<<3
+#define  BAK_ERR_DB         1<<4
+#define  BAK_ERR_WE_LEAK    1<<5
+#define  BAK_ERR_DEBUG      1<<7
+
+#define  LEN_ADPC_DATE_BUF  4096
+
+
+
+//#define ADPC_DEBUG         1
+
+
+#endif
+
+
+
+/************************************END********************************/