#ifndef __UART_USER_H__
#define __UART_USER_H__

#include "type.h"
#include "config.h"
#include "igpio.h"


//---------------------------------------------

#define UART_ONESHU_CLOSED      0
#define NO_USE                  0
#define __LINUX_SYS_TIME__      1
#define RS485_GPIO_NUM_DE       GPIO_NUM_1_1


//---------------------------------------------

#define UART_USER_232_COM    1
#define UART_USER_485_COM    2


#define RS232_NUM      8
#define RS232_HEAD     0x47
#define RS232_WEEPROM  0X82
#define RS232_WSPECIAL 0X84
#define RS232_TAILH    0x0d
#define RS232_TAILL    0x0a
typedef enum
{
   OUT_HEAD    ,
   OUT_COMMAND ,
   OUT_ADDRH   ,
   OUT_ADDRL   ,
   OUT_DATA    ,
   OUT_CHECKSUM,
   OUT_TAILH   ,
   OUT_TAILL
}OUT_ENUM;

enum
{
    UART_PARA_SET_ERR_OK = 0,
    UART_PARA_SET_ERR_LOCAL,
    UART_PARA_SET_ERR_INVALID,
    UART_PARA_SET_ERR_SUM,
    UART_PARA_SET_ERR_DRYLOOP,
    UART_PARA_SET_ERR_AGC_ON,
    UART_PARA_SET_ERR_UNKNOW_CMD,
};

typedef enum    //CMMB与EXCITER共用
{
    CMMB_CONFIG_STEP_9V_VOL=0xa0,
    CMMB_CONFIG_STEP_50V_VOL,
    CMMB_CONFIG_STEP_50V_CUR,
    CMMB_CONFIG_STEP_881_GV,
    CMMB_CONFIG_STEP_FWD,
    CMMB_CONFIG_STEP_REF,
    CMMB_CONFIG_STEP_VSWR,
    CMMB_CONFIG_STEP_TEMP,
    CMMB_CONFIG_STEP_REF_ALARM,
    CMMB_CONFIG_STEP_FWD_ALARM,
    CMMB_CONFIG_STEP_TEMP_ALARM,

    CMMB_CONFIG_STEP_50V_CUR2,
    CMMB_CONFIG_STEP_POWER_DEGREE,
    CMMB_CONFIG_STEP_FWD_HEX,
    CMMB_CONFIG_STEP_IP_ADDR,
    CMMB_CONFIG_STEP_MASK_ADDR,   //0xaf
    CMMB_CONFIG_STEP_GATEWAY_ADDR,

    CMMB_CONFIG_STEP_50V_CUR3,
    CMMB_CONFIG_STEP_50V_CUR4,
    CMMB_CONFIG_STEP_IN,
    CMMB_CONFIG_STEP_12V_VOL,

    CMMB_CONFIG_STEP_SLOW_FLAG,   //向ATSC激励器发送缓开机标识
    CMMB_CONFIG_STEP_FINE_POWER,
    CMMB_CONFIG_STEP_ALARM,

    CMMB_CONFIG_EXC_RESET,//远程复位atsc激励器
    
    CMMB_CONFIG_STEP_OVER,
}EXCITER_SET_CMD;

extern uint32 uart_init_set_result_frame(uint8 *pin,uint8 *pout,uint32 err);
extern void e2rom_save_power(S_RF_PARA *ppara);
extern uint32 get_menu_index(void);
extern BOOL proc_key_update(void * parg, uint8 key);
extern uint32 get_menu_index(void);
extern uint32 protocol_read(uint8 *pbufin,uint8 *pbufout);
extern uint32 protocol_write(uint8 *pbufin,uint8 *pbufout);

extern void pa_conn_chk(void);
uint32 pa_conn_sta(void);

void uart_task(void * pvParameters);
extern int creat_uart_thread(void);


extern void dev_pa_link_sec_check(void);
extern int creat_uart_thread(void);
extern int rs485_send_string(const uint8 *pbuf,uint32 len);
extern int gps_uart_hw_init(void);
extern int gps_rs232_read_string(uint8 *pbuf,uint32 len);
extern int gps_rs232_send_string(const uint8 *pbuf,uint32 len);

extern int rs232_send_string(const uint8 *pbuf,uint32 len);
extern int rs232_read_string(uint8 *pbuf,uint32 len);

#endif